Name: Acrylic Display Case Compatible with LEGO® WALL-E and EVE 43279
Brand: brickzonehub
Rating: 5.0 (2 reviews)

Question 1

How do I pick the right display case size for LEGO Harry Potter 76391 Hogwarts Icons?

Accepted Answer

Start with the set’s built size: Hogwarts Icons 76391 is roughly 44 cm high, 50 cm wide and 33 cm deep. When you choose a case, make sure the internal space is at least 2–3 cm bigger in every direction so Hedwig’s wings, the bottles and the letter aren’t pressed up against the acrylic. Always check the internal measurements, not just the overall outside size.

Question 2

How do I know if my LEGO Hogwarts Castle and Grounds 76419 will actually fit in a display case?

Accepted Answer

The castle and grounds measure about 21 cm high, 35 cm wide and 25 cm deep once built. Look for a case that gives you a couple of extra centimetres on the width and depth, and at least 3–4 cm spare above the highest tower. That extra “breathing room” makes it much easier to place the model without knocking off trees or turrets.

Question 3

How can I check if LEGO Harry Potter Diagon Alley 75978 will fit along my shelf and inside a case?

Accepted Answer

Diagon Alley 75978 is a long one – the model is just over 1 metre wide, around 29 cm high and 13 cm deep. Measure your shelf and the display case length carefully and make sure you’ve got at least 3–5 cm spare along the length and 2–3 cm spare on the depth. That way you’re not shoving the buildings right up against the front panel or the back wall.

Question 4

How should I handle and assemble an acrylic display case so I don’t scratch it?

Accepted Answer

Lay everything out on a clean, soft surface – an old cotton T-shirt or microfibre cloth works well. Peel the protective film slowly from one corner rather than digging at it with your nails. When you tighten screws, stop as soon as the panels feel snug; over-tightening can stress the acrylic and leave hairline marks.

Question 5

How do I move LEGO Hogwarts Icons 76391 safely into a display case without bits falling off?

Accepted Answer

Take off the loose bits first – the letters, potion bottles and minifigures. Then lift the build by supporting the base and the spellbook together, rather than grabbing Hedwig or a single corner. Pop the main build into the case, get it centred, and only then place the small accessories back around it.

Question 6

How do I stop the minifigures and potion bottles on 76391 wobbling or falling over inside the case?

Accepted Answer

Where possible, keep everything attached to the original LEGO studs or display plates. If you want extra security, you can sit the plates on clear 1x1 round tiles or use tiny clear museum putty dots under the bases. They’re removable, but they give a bit more grip if the case gets nudged.

Question 7

How should I set up a Hogwarts display case if I’ve got young children or pets in the house?

Accepted Answer

Put the case on a sturdy unit that’s out of the main traffic route – not right by a doorway or in the middle of a low coffee table. Add a few rubber pads or non-slip feet under the base so the case can’t slide if it’s bumped. If it’s on a high shelf against a wall, you can also use discreet anti-tip brackets for extra peace of mind.

Question 8

How do I clean an acrylic Harry Potter display case without leaving scratches or cloudy marks?

Accepted Answer

Use a soft microfibre cloth with plain water or a tiny drop of mild washing-up liquid. Wipe gently and then dry with another clean cloth. Avoid kitchen roll, glass cleaner, alcohol wipes or anything abrasive – they can all scratch or haze the acrylic over time.

Question 9

How can I protect my LEGO bricks from yellowing or fading while they’re in a display case?

Accepted Answer

Keep the case out of direct sunlight where you can – especially near south-facing windows. Warm white LED strips are better than harsh spotlights, and it helps to run them for a few hours at a time rather than leaving them on all day. The case will cut down dust, but UV is what really fades white and light-coloured bricks.

Question 10

How do I line up a Hogwarts-themed printed backdrop inside the case so it doesn’t look wonky?

Accepted Answer

Before you tighten anything, “dry fit” the backdrop and close the case loosely so you can see it from the front. Line up key elements – such as the castle silhouette or Hogwarts crest – with the centre of your model. Once you’re happy, open the case, hold the backdrop firmly against the rear panel and only then tighten the screws evenly from side to side.

Question 11

What’s the best way to unpack a Harry Potter display case delivery so I’m covered if anything arrives damaged?

Accepted Answer

Open the parcel carefully and take a few quick photos of the outer box, the internal packaging and each panel as it comes out. If you spot cracks or deep scratches straight away, keep all the packaging, take close-ups of the problem and contact customer service with your order number and photos. That’s usually enough for a quick replacement or refund.

Question 12

How do I pack my Hogwarts display case if I’m moving house and don’t want to fully dismantle the LEGO set?

Accepted Answer

Remove the lid and front panel, then lift the whole LEGO build and base out together if possible. Wrap the model and base in bubble wrap or a soft blanket. Pack the acrylic panels separately with cardboard between them. In the van or car, keep the model flat and fully supported so it can’t slide or tip during the journey.

Question 13

How should I set up lighting around a Hogwarts case so it looks magical but not over the top?

Accepted Answer

LED strip lights behind or underneath the case work really well – they give a soft glow without shining straight in your eyes. For Harry Potter sets a warm white (around 3000–3500K) feels cosy and “wizarding world”; if you want more of a moody night-time look, add a subtle cooler accent from above to mimic moonlight.

Question 14

What details do I need to give customer service if I’d like a custom-sized display case for a specific Harry Potter set?

Accepted Answer

Measure the model’s full height, width and depth, including anything that sticks out like flags, trees or the Whomping Willow. Then measure the shelf or cabinet you want to use. When you email or message, include the set number (for example 76391, 76419, 75978 or 76405), your measurements, and ideally a quick photo. That’s usually enough for them to suggest a sensible internal size.

Question 15

How do I check if a Hogwarts display case will fit inside my IKEA unit (like BILLY or BESTÅ)?

Accepted Answer

Measure the usable space inside the shelf – width, depth and height – with the doors closed if you have glass doors. Compare those numbers with the external measurements of the display case and make sure you’ve got at least 1–2 cm clearance on all sides, otherwise getting the case in and out will be a bit of a faff.

Question 16

How can I safely take the front off a screwed-together case to dust or rearrange my Hogwarts build?

Accepted Answer

Work slowly and take out the screws from the top and one side first, keeping a hand on the panel so it doesn’t drop. Leave the base and back panel in place so the LEGO set stays stable. Once you’ve finished dusting or posing minifigures, refit the panel and tighten the screws just until they’re snug – there’s no need to really crank them down.

Question 17

Why should I bother buying a display case for LEGO Harry Potter 76391 instead of leaving it on an open shelf?

Accepted Answer

Hogwarts Icons is packed with exposed detail: owls’ feathers, glass bottles, letters and books, all of which are dust magnets. Once dust settles in, cleaning around the feathers and bottle tops is a nightmare. A case keeps dust, knocks and curious hands off the build, so it stays looking like a collector’s piece rather than something that’s been sat on a shelf for years.

Question 18

Why is a purpose-built acrylic case better than using a random glass fish tank or storage box?

Accepted Answer

Good-quality acrylic is lighter than glass and much more impact-resistant, so if it does get knocked it’s less likely to shatter. A made-to-measure case will also be sized around the exact set – height, depth and viewing angle – whereas a fish tank or storage tub tends to waste space, distort the view and make it harder to get the model in and out.

Question 19

Why do long Harry Potter sets like Diagon Alley 75978 or Hogwarts Express 76405 really benefit from a dedicated case?

Accepted Answer

Diagon Alley is over a metre wide and Hogwarts Express 76405 is even longer at about 118 cm. With something that big, open display means more dust, more risk of being caught by elbows, and less flexibility if you ever need to move it. A long, side-opening display case lets you protect the whole scene in one go, with room for track, figures and lighting built in.

Question 20

Why shouldn’t a display case be exactly the same size as the LEGO set dimensions?

Accepted Answer

If the internal size is identical to the LEGO measurements, there’s no allowance for small shifts when you move the model or for pieces that sit a bit higher after rebuilding. Just 2–3 cm extra on each dimension makes a huge difference – the set is easier to place, you’re less likely to scrape towers or owls on the way in, and you can reach in to fix a loose bit without dismantling half the build.

Question 21

Why do most display case brands tell you not to use glass cleaner or alcohol on acrylic panels?

Accepted Answer

Standard glass cleaners often contain ammonia or alcohol, which can react with acrylic, leading to micro-cracks, cloudy patches or a “crazed” look over time. Using simple water or a mild detergent with a soft cloth keeps the panels clear for much longer and avoids weakening them around the screw holes or edges.

Question 22

Why is it important to check that the display case doesn’t include the LEGO set itself?

Accepted Answer

High-end sets like Hogwarts Icons 76391, Hogwarts Castle and Grounds 76419 or Diagon Alley 75978 are expensive on their own. A display case listing is almost always “case only, LEGO not included”. Double-checking that line before you buy avoids any disappointment and makes it clear you’re buying protection and presentation for a set you already own (or are planning to pick up separately).

Question 23

Why do so many collectors choose to put Hogwarts Castle and Grounds 76419 in a case even though it’s a smaller footprint?

Accepted Answer

76419 is a compact footprint but packed with tiny towers, trees and rocky details. Once dust gets into the crevices and around the micro-turrets, cleaning is really fiddly. A case turns it into a contained, moveable display – you can treat it like a centrepiece on a sideboard or office shelf without worrying about daily dusting.

Question 24

Where’s the best place in my home to put a Harry Potter display case?

Accepted Answer

Ideally somewhere you walk past and can enjoy, but not where people are constantly brushing against it – so a solid sideboard, bookcase or dedicated display unit is perfect. Try to avoid direct sunlight, radiators and the main route between the sofa and the kitchen, where things tend to get knocked.

Question 25

Where should I not put a Hogwarts display case if I want it to last?

Accepted Answer

Avoid window sills with strong sun, spots directly under air-con vents, and wobbly floating shelves. Direct heat and UV can warp or fade both the bricks and the acrylic, and constant airflow blows dust onto any tiny gap. Anywhere that vibrates or flexes – like the top of a very slim shelving unit – is also best avoided for heavier sets like 75978 or 76405.

Question 26

If I’m in the UK, where will my Harry Potter display case usually ship from and how long does it take?

Accepted Answer

Most UK-focused display brands dispatch from UK warehouses and use carriers like Royal Mail, DPD or similar couriers. Standard delivery is typically around a week once it’s been packed, with tracking details sent by email. Always check the shipping page for current UK timeframes and any cut-off times in busy periods like Christmas.

Question 27

Where do I go if there’s an issue with my order – cracks, missing parts or the wrong size?

Accepted Answer

Use the contact details on the website – usually a support email address and/or a contact form. Include your order number, photos of the problem and the measurements you expected. A decent UK retailer will review the evidence and offer a replacement panel, full swap or refund, depending on what’s gone wrong.

Question 28

Which Harry Potter set should I prioritise for a display case if I only have budget for one right now?

Accepted Answer

If you’ve got several big sets, most collectors in the UK tend to prioritise: Hogwarts Icons 76391 – lots of delicate exposed detail and light-coloured parts. Diagon Alley 75978 – huge footprint and intricate shopfronts. Hogwarts Castle and Grounds 76419 – dense micro-detail that’s tedious to dust. Protecting the most detailed and time-consuming builds first usually gives you the best return on your spend.

Question 29

Which style of display is better for Hogwarts sets if I’m short on floor space – tabletop cases or wall-mounted units?

Accepted Answer

If you’re renting or don’t want to drill into walls, a tabletop case on a sturdy cabinet is the safer bet and easier to move when you rearrange. Wall-mounted setups look brilliant for long sets like Diagon Alley, but you’ll want very secure fixings into solid walls and to stay well within the weight rating of the brackets.

Question 30

Which Hogwarts sets benefit most from upgrading from a generic box to a dedicated themed case?

Accepted Answer

Long or tall centrepieces see the biggest improvement – for example: Diagon Alley 75978 – needs length and front viewing space. Hogwarts Express 76405 – needs length and side access along the train. A themed Hogwarts backdrop, nameplate space and properly thought-through dimensions make these look more like a premium display than a set stored in a random tub.

Question 31

Which background artwork suits different rooms – living room, games room or a child’s bedroom?

Accepted Answer

Living room: calmer castle panoramas, night-sky or film-poster-style artwork that doesn’t clash with the rest of the décor. Games room / home office: bolder colours, dramatic stormy skies or spell effects, sometimes with accent lighting. Children’s bedroom: brighter, more playful illustrations of Hogwarts and the Express – nothing too dark or gloomy if it’s near the bed.

Question 32

What normally comes in the box with a Harry Potter display case?

Accepted Answer

Typically you’ll get: pre-cut acrylic panels, a base or support frame, screws or connectors, any printed Hogwarts backdrop or nameplate, plus a simple assembly guide or QR code link to instructions. Unless it’s clearly stated, you should always assume the LEGO set itself is not included.

Question 33

What thickness of acrylic is used for large Harry Potter display cases, and what difference does it make?

Accepted Answer

Most decent cases use around 3 mm acrylic for smaller builds and 4–5 mm for bigger ones. Thicker panels feel more solid on long spans (for example Diagon Alley or Hogwarts Express) and are less prone to flexing or bowing, especially if you move the case with the set inside.

Question 34

What should I send to customer service if the parcel turns up with damaged acrylic panels?

Accepted Answer

Take photos of: The outside of the shipping box, showing any dents or tears; The inside packaging and how the panels were protected; Close-ups of each cracked or badly scratched panel; The shipping label and your order number. Attach these to your email or message. For UK orders, that’s normally enough for the team to claim with the courier and sort a replacement for you without a lot of back-and-forth.

Question 35

What does a good Harry Potter display case actually do beyond just keeping dust off?

Accepted Answer

A well-designed case: Protects against knocks and curious hands; Slows down UV-related fading from everyday light; Gives you space for neat lighting and minifigure posing; Frames the set so it feels like a proper centrepiece in your living room or office. For high-end sets like 76391, 75978, 76419 or 76405, that extra protection and presentation helps them feel more like a long-term collectible than just another toy on a shelf.

Item added to your cart

Acrylic Display Case Compatible with LEGO® WALL-E and EVE 43279

Acrylic Display Case Compatible with LEGO® WALL-E and EVE 43279

Product Description

Key Features:

Quality You Can See

For LEGO® Disney Fans

Installation

Room Ideas

Cyberpunk Game

Industrial Racing

Modern Living

FAQ

Will this display case fit my LEGO® set?

Can I request a custom size?

How long will it take to receive my order?

What if my product arrives damaged?

What are your cases made of?

Display, done right.

Free Shipping

30-Day Guarantee

Made for LEGO Fans

Brickzonehub Club

Collector Graded

Customer Review

Lego Display Tips

LEGO Star Wars Diorama Display Cases UK | Minif...

LEGO Star Wars Diorama Display Cases UK | Minif...

LEGO Star Destroyer Display Case UK | Premium D...

LEGO Star Destroyer Display Case UK | Premium D...

LEGO Star Wars Display Cases UK | Dust-Free Acr...

LEGO Star Wars Display Cases UK | Dust-Free Acr...

How to Display Star Wars LEGO Sets: The Complet...

How to Display Star Wars LEGO Sets: The Complet...

Country/region

Language